|
|
| |
| Lighting \ CoolSpot II |
Technical Information
| General Information
The CoolSpot II Light was designed to provide a compact source of intense, narrow field illumination for a wide range of examination and procedural needs. The CoolSpot II provides long bulb life and low heat build-up due to its low voltage systems.
Approvals
Listed by UL (Underwriters Laboratories), CSA Certified.
Materials
Light Housing: aluminum
Yoke and arm/pivot adapters: aluminum
Yoke cover/arm tube: steel
Electrical Characteristics
Input Voltage: 115 volts AC, 60 Hz (cycles), single phase (may be wired for 230 volts AC, 50/60 Hz)
Input Current: 1.5 amperes (115 volts) or 0.75 amperes (230 volts)
Input Power: 150 watts
Bulb Type: EKE tungsten halogen with integral dichroic reflector, 21.0 volts, 150 watts, operated at 19 volts for normal operation and 21 volts for higher intensity.
Bulb Life: 500 hours average.
Power Cord: Ceiling mounts are directly wired in. Floor stand base and wall mount have SJT 18 AWG 3 wire 6' long power cords with a hospital grade plug.
Power Switch: Power Switch-Push button, rated 12 A at 250 volts AC, double pole single throw for On/Off. Intensity control switch-paddle type, rated 20 A at 120 volts AC
Lamp Socket: Dual pin; ceramic
Current Leakage: Less than 100 micro amperes
Optical Characteristics| Distance (inches) (ft-cd) | Intensity | Spot Diameter | | 18 | 9,200 - 14,500 (footcandles) | 1.5 - 4.5 (in) | | 24 | 5,500 - 8,000 (footcandles) | 2.0 - 7.0 (in) | | 36 | 2,700 - 4,000 (footcandles) | 6.0 - 12.0 (in) |
Color temperature: Approximately 3,600° Kelvin.
Infrared in the beam: Less than 25 milliwatts/square cm/fc (to IES standard).
Lighthead and Arm
Lighthead has three "legs": 8" from head axis to end of each leg, 4" head thickness, 26" (66 cm) from head pivot to arm attachment axis. Head supplied standard with sterilizable handle. Head pivots 170 degrees on its yoke. The yoke pivots 340 degrees on the flexible arm. The flexible arm pivots 40 degrees above and below horizontal, for a total angular travel of 80 degrees. (Vertical reach is therefore, 31".).
Floorstand Base
Maximum over all dimensions: 18" (46 cm) side to side, 19" (48 cm) front to back, 4.5" (11.4 cm) to top of legs. Includes four continuous swivel non-conductive casters.
Floorstand Upright
Maximum over all height installed in base: 66" (168 cm), 1.5" (3.2 cm); diameter: with head pointing down, distance from floor to front face is adjustable from 44" to 72" (112 cm to 183 cm). Head and arm pivot 40 degrees between floorstand base legs.
Single Ceiling Mount
12" (30.5 cm) diameter mounting plate and cover attaches to reinforced ceiling with three fasteners 3/8" diameter (9.5 mm) located on an 8" (208 mm) diameter hole circle, electrical input wires routed through a 2" (50.8 mm) cutout. Contains one ceiling mount pole which allows installation in rooms with ceilings up 9.5' high (2.89 m) based on installing the arm at 80" (203 cm) above the floor. Contains one fixed horizontal extension arm which is 17" (431.8 mm) from pivot to pivot. The extension arm pivots 320 degrees on the ceiling mounting pole. The flexible arm pivots 320 degrees on the extension arm. Maximum reach is 43" (1.09 m) from the ceiling pole axis to the lighthead pivot.
Double Ceiling Mount
Mounting plate, cover, pole and extension arm dimensions, pivot data, and reach data same as Single Ceiling Mount. Contains two extension arms.
Wall Mount
7" (177.8 mm) high, 6" (152.4 mm) wide casting attaches to a main wall structural member (stud) or reinforcement as necessary with two fasteners 3/8" diameter. Casting extends 6" away from the wall. Contains one extension arm, 17" from pivot to pivot. Extension arm pivots 180 degrees on wall mount. Flexible arm pivots approximately 320 degrees on extension arm.
Finish
All products are painted light gray as a standard finish. Custom colors are available at additional charge – call for quotation.
|
|
|
|
|
|
|
|
